Tuesday, October 11, 2011

Multiserver Setup With Dedicated Web, Email, DNS & MySQL Database Servers On Debian Squeeze With ISPConfig 3


This tutorial describes the installation of an ISPConfig 3 multiserver setup with dedicated web, email, database and two DNS servers all managed trough a single ISPConfig 3 control panel. The setup described below uses five servers and can be extended easily to to a higher number of servers by just adding more servers. E.g. if you want to have two mailservers, do the setup steps from chapter 2 on both of these servers. If you want to set up more web servers, then install ISPConfig on all other web servers in expert mode except of the first one.

1 Installing The Five Debian Base Systems

In this setup there will be one master server (which runs the web server and ISPConfig control panel interface) and four slave servers for database, email and DNS.
To install the clustered setup, we need five servers (or virtual servers) with a Debian 5.0 minimal install. The base setup is described in the following tutorial in the steps 1 - 6:
http://www.howtoforge.com/perfect-server-debian-squeeze-with-bind-and-dovecot-ispconfig-3
Install only steps 1 - 6 of the perfect server tutorial and not the other steps as they differ for a clustered setup!
In my example I use the following hostnames and IP addresses for the five servers:
Web Server
Hostname: web.example.tld
IP address: 192.168.0.105
Mail Server
Hostname: mail.example.tld
IP address: 192.168.0.106
DB Server
Hostname: db.example.tld
IP address: 192.168.0.107
DNS Server (primary)
Hostname: ns1.example.tld
IP address: 192.168.0.108
DNS Server (secondary)
Hostname: ns2.example.tld
IP address: 192.168.0.109
Whereever these hostnames or IP addresses occur in the next installation steps you will have to change them to match the IP's and hostnames of your servers.

2 Installing The Web Server

Edit the hosts file and add the IP addresses and hostnames for all servers. The hostnames and IP addresses have to be adjusted to match your setup.
vi /etc/hosts
127.0.0.1       localhost
192.168.0.105   web.example.tld
192.168.0.106   mail.example.tld
192.168.0.107   db.example.tld
192.168.0.108   ns1.example.tld
192.168.0.109   ns2.example.tld
 
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Set the hostname of the server:
echo web.example.tld > /etc/hostname
/etc/init.d/hostname.sh start
Run...
apt-get update
... to update the apt package database; then run...
apt-get upgrade
... to install the latest updates (if there are any).
It is a good idea to synchronize the system clock with an NTP (network time protocol) server over the Internet. Simply run...
apt-get -y install ntp ntpdate
... and your system time will always be in sync.
Install the MySQL server. A MySQL server instance is necessary on every server as ISPConfig uses it to sync the configuration between the servers.
apt-get -y install mysql-client mysql-server
Enter the new password for MySQL when requested by the installer.
We want MySQL to listen on all interfaces on the master server, not just localhost, therefore we edit /etc/mysql/my.cnf and comment out the line bind-address = 127.0.0.1:
vi /etc/mysql/my.cnf
[...]  

# Instead of skip-networking the default is now to listen only on  
# localhost which is more compatible and is not less secure.  
#bind-address           = 127.0.0.1  

[...]
Then restart MySQL:
/etc/init.d/mysql restart
Now install Apache2, PHP5, phpMyAdmin, FCGI, suExec, Pear, and mcrypt as follows:
apt-get -y install apache2 apache2.2-common apache2-doc apache2-mpm-prefork apache2-utils libexpat1 ssl-cert libapache2-mod-php5 php5 php5-common php5-gd php5-mysql php5-imap phpmyadmin php5-cli php5-cgi libapache2-mod-fcgid apache2-suexec php-pear php-auth php5-mcrypt mcrypt php5-imagick imagemagick libapache2-mod-suphp libopenssl-ruby libapache2-mod-ruby sudo zip wget
You will see the following question:
Web server to reconfigure automatically: <-- apache2
Then run the following command to enable the Apache modules suexec, rewrite, ssl, actions, and include:
a2enmod suexec rewrite ssl actions include ruby dav_fs dav auth_digest
PureFTPd and quota can be installed with the following command:
apt-get -y install pure-ftpd-common pure-ftpd-mysql quota quotatool
Edit the file /etc/default/pure-ftpd-common...
vi /etc/default/pure-ftpd-common
... and make sure virtualchroot is set VIRTUALCHROOT=true:
[...]
VIRTUALCHROOT=true
[...]
Now we configure PureFTPd to allow FTP and TLS sessions. FTP is a very insecure protocol because all passwords and all data are transferred in clear text. By using TLS, the whole communication can be encrypted, thus making FTP much more secure.
If you want to allow FTP and TLS sessions, run
echo 1 > /etc/pure-ftpd/conf/TLS
In order to use TLS, we must create an SSL certificate. I create it in /etc/ssl/private/, therefore I create that directory first:
mkdir -p /etc/ssl/private/
Afterwards, we can generate the SSL certificate as follows:
openssl req -x509 -nodes -days 7300 -newkey rsa:2048 -keyout /etc/ssl/private/pure-ftpd.pem -out /etc/ssl/private/pure-ftpd.pem
Country Name (2 letter code) [AU]: <-- Enter your Country Name (e.g., "DE").
State or Province Name (full name) [Some-State]:
<-- Enter your State or Province Name.
Locality Name (eg, city) []:
<-- Enter your City.
Organization Name (eg, company) [Internet Widgits Pty Ltd]:
<-- Enter your Organization Name (e.g., the name of your company).
Organizational Unit Name (eg, section) []:
<-- Enter your Organizational Unit Name (e.g. "IT Department").
Common Name (eg, YOUR name) []:
<-- Enter the Fully Qualified Domain Name of the system (e.g. "server1.example.com").
Email Address []:
<-- Enter your Email Address.
Change the permissions of the SSL certificate:
chmod 600 /etc/ssl/private/pure-ftpd.pem
Then restart PureFTPd:
/etc/init.d/pure-ftpd-mysql restart
Edit /etc/fstab. Mine looks like this (I added ,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0 to the partition with the mount point /):
vi /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
#                
proc            /proc           proc    defaults        0       0
# / was on /dev/sda1 during installation
UUID=92bceda2-5ae4-4e3a-8748-b14da48fb297 /               ext3    errors=remount-ro,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0 0       1
# swap was on /dev/sda5 during installation
UUID=e24b3e9e-095c-4b49-af27-6363a4b7d094 none            swap    sw              0       0
/dev/scd0       /media/cdrom0   udf,iso9660 user,noauto     0       0
/dev/fd0        /media/floppy0  auto    rw,user,noauto  0       0
To enable quota, run these commands:
mount -o remount /
quotacheck -avugm
quotaon -avug
Install vlogger, webalizer, and awstats:
apt-get -y install vlogger webalizer awstats
Open /etc/cron.d/awstats afterwards...
vi /etc/cron.d/awstats
... and comment out both cron jobs in that file:
#*/10 * * * * www-data [ -x /usr/share/awstats/tools/update.sh ] && /usr/share/awstats/tools/update.sh

# Generate static reports:
#10 03 * * * www-data [ -x /usr/share/awstats/tools/buildstatic.sh ] && /usr/share/awstats/tools/buildstatic.sh
Install Jailkit: Jailkit is needed only if you want to chroot SSH users. It can be installed as follows (important: Jailkit must be installed before ISPConfig - it cannot be installed afterwards!):
apt-get -y install build-essential autoconf automake1.9 libtool flex bison debhelper
cd /tmp
wget http://olivier.sessink.nl/jailkit/jailkit-2.14.tar.gz
tar xvfz jailkit-2.14.tar.gz
cd jailkit-2.14
./debian/rules binary
cd ..
dpkg -i jailkit_2.14-1_*.deb
rm -rf jailkit-2.14*
Install fail2ban: This is optional but recommended, because the ISPConfig monitor tries to show the log:
apt-get install fail2ban
To make fail2ban monitor PureFTPd, create the file /etc/fail2ban/jail.local:
vi /etc/fail2ban/jail.local
[pureftpd]

enabled  = true
port     = ftp
filter   = pureftpd
logpath  = /var/log/syslog
maxretry = 3
Then create the following filter file:
vi /etc/fail2ban/filter.d/pureftpd.conf
[Definition]
failregex = .*pure-ftpd: \(.*@\) \[WARNING\] Authentication failed for user.*
ignoreregex =
Restart fail2ban afterwards:
/etc/init.d/fail2ban restart
Next we will install ISPConfig 3. To get the download URL of the latest ISPConfig 3 stable release, please visit the ISPConfig website: http://www.ispconfig.org/ispconfig-3/download/
This server is the master server in our setup which runs the ISPConfig control panel interface. To allow the other MySQL instances to connect to the MySQL database on this node during installation, we have to add MySQL root user records in the master database for every slave server hostname and IP address. The easiest way to do this is to use the web based phpmyadmin administration tool that we installed already. Open the URL http://192.168.0.105/phpmyadmin in a web browser, log in as MySQL root user and execute these MySQL queries:
CREATE USER 'root'@'192.168.0.106' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'192.168.0.106' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'192.168.0.107' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'192.168.0.107' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'192.168.0.108' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'192.168.0.108' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'192.168.0.109' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'192.168.0.109' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'mail.example.tld' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'mail.example.tld' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'db.example.tld' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'db.example.tld' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'ns1.example.tld' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'ns1.example.tld' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
CREATE USER 'root'@'ns2.example.tld' IDENTIFIED BY 'myrootpassword';
GRANT ALL PRIVILEGES ON * . * TO 'root'@'ns2.example.tld' IDENTIFIED BY 'myrootpassword' WITH GRANT OPTION MAX_QUERIES_PER_HOUR 0 MAX_CONNECTIONS_PER_HOUR 0 MAX_UPDATES_PER_HOUR 0 MAX_USER_CONNECTIONS 0 ;
In the above sql commands, replace the IP adresses (192.168.0.106 - 192.168.0.109) with the IP addresses of your servers and replace mail.example.tld, db.example.tld, ns1.example.tld and ns2.example.tld with the hostnames of your servers and myrootpassword with the desired root password.
Click on the reload permissions button or restart MySQL. Then close phpmyadmin.
Go back to the shell of server1.example.tld and download the latest ISPConfig 3 stable release:
cd /tmp
wget http://www.ispconfig.org/downloads/ISPConfig-3-stable.tar.gz
tar xfz ISPConfig-3-stable.tar.gz
cd ispconfig3_install/install/
Then start the install script:
php -q install.php
Select language (en,de) [en]: <-- en
Installation mode (standard,expert) [standard]: <-- expert
Full qualified hostname (FQDN) of the server, eg server2.domain.tld [web.example.tld]: <-- web.example.tld
MySQL server hostname [localhost]: <-- localhost
MySQL root username [root]: <-- root
MySQL root password []: <-- Enter your MySQL root password here
MySQL database to create [dbispconfig]: <-- dbispconfig
MySQL charset [utf8]: <-- utf8
Shall this server join an existing ISPConfig multiserver setup (y,n) [n]: <-- n
Configure Mail (y,n) [y]: <-- n
Configure Jailkit (y,n) [y]: <-- y
Configure FTP Server (y,n) [y]: <-- y
Configure DNS Server (y,n) [y]: <-- n
Configure Apache Server (y,n) [y]: <-- y
Configure Firewall Server (y,n) [y]: <--y
Install ISPConfig Web-Interface (y,n) [y]: <--y
ISPConfig Port [8080]: <-- 8080
Enable SSL for the ISPConfig web interface (y,n) [y]:
<-- y
Country Name (2 letter code) [AU]: <-- ENTER
State or Province Name (full name) [Some-State]: <-- ENTER
Locality Name (eg, city) []: <-- ENTER
Organization Name (eg, company) [Internet Widgits Pty Ltd]: <-- ENTER
Organizational Unit Name (eg, section) []: <-- ENTER
Common Name (eg, YOUR name) []: <-- ENTER
Email Address []: <-- ENTER
A challenge password []: <-- ENTER
An optional company name []:
<-- ENTER
Clean up the install directories:
cd /tmp
rm -rf /tmp/ispconfig3_install/install
rm -f /tmp/ISPConfig-3-stable.tar.gz

3 Installing The Mail Server

 
Edit the hosts file and add the IP addresses and hostnames for all servers. The hostnames and IP addresses have to be adjusted to match your setup.
vi /etc/hosts
127.0.0.1       localhost
192.168.0.105   web.example.tld
192.168.0.106   mail.example.tld
192.168.0.107   db.example.tld
192.168.0.108   ns1.example.tld
192.168.0.109   ns2.example.tld
 
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Set the hostname of the server:
echo mail.example.tld > /etc/hostname
echo mail.example.tld > /etc/mailname
/etc/init.d/hostname.sh start
Run...
apt-get update
... to update the apt package database; then run...
apt-get upgrade
... to install the latest updates (if there are any).
It is a good idea to synchronize the system clock with an NTP (network time protocol) server over the Internet. Simply run...
apt-get -y install ntp ntpdate
... and your system time will always be in sync.
Install postfix, dovecot and MySQL with one single command:
apt-get -y install postfix postfix-mysql postfix-doc mysql-client mysql-server openssl getmail4 rkhunter binutils dovecot-imapd dovecot-pop3d
Enter the new password for mysql when requested by the installer and answer the next questions as decsribed below:
General type of configuration? <-- Internet site
Mail name?
<-- mail.mydomain.tld
To install amavisd-new, SpamAssassin, and ClamAV, we run:
apt-get -y install amavisd-new spamassassin clamav clamav-daemon zoo unzip bzip2 arj nomarch lzop cabextract apt-listchanges libnet-ldap-perl libauthen-sasl-perl clamav-docs daemon libio-string-perl libio-socket-ssl-perl libnet-ident-perl zip libnet-dns-perl
If you want to use mailinglists on your server, then install mailman. This step is optional. mailman requires a apache webserver, so if you dont want to run a apache instance on your mailserver, then dont install mailman.
apt-get -y install mailman
The apt installer for mailman will ask you then to select the languages for the mailing list. Enable all languages that you want to use for mailman. Next create the "mailman" mailinglist.
newlist mailman
and enter the email address and new password for the mailinglist administrator. Thats the last step of the mailman install. The next command to install php has to be executed on every server, independently if you installed mailman or not.
Then install install the commandline version of PHP to be able to run PHP-based shell scripts for ISPConfig:
apt-get -y install php5-cli php5-mysql php5-mcrypt mcrypt
Install fail2ban: This is optional but recommended, because the ISPConfig monitor tries to show the log:
apt-get install fail2ban
To make fail2ban monitor PureFTPd and Dovecot, create the file /etc/fail2ban/jail.local:
vi /etc/fail2ban/jail.local
[dovecot-pop3imap]

enabled = true
filter = dovecot-pop3imap
action = iptables-multiport[name=dovecot-pop3imap, port="pop3,pop3s,imap,imaps", protocol=tcp]
logpath = /var/log/mail.log
maxretry = 5
Then create the following filter file:
vi /etc/fail2ban/filter.d/dovecot-pop3imap.conf
[Definition]
failregex = (?: pop3-login|imap-login): .*(?:Authentication failure|Aborted login \(auth failed|Aborted login \(tried to use disabled|Disconnected \(auth failed|Aborted login \(\d+ authentication attempts).*rip=(?P\S*),.*
ignoreregex =
Restart fail2ban afterwards:
/etc/init.d/fail2ban restart
Now I will install ISPConfig 3 on this server. To get the download URL of the latest ISPConfig 3 stable release, please visit the ISPConfig website: http://www.ispconfig.org/ispconfig-3/download/
Download the latest ISPConfig 3 stable release:
cd /tmp
wget http://www.ispconfig.org/downloads/ISPConfig-3-stable.tar.gz
tar xfz ISPConfig-3-stable.tar.gz
cd ispconfig3_install/install/
Then start the install script:
php -q install.php
Select language (en,de) [en]: <-- en
Installation mode (standard,expert) [standard]: <-- expert
Full qualified hostname (FQDN) of the server, eg server1.domain.tld [mail.example.tld]: <-- mail.example.tld
MySQL server hostname [localhost]: <-- localhost
MySQL root username [root]: <-- root
MySQL root password []: <-- Enter your MySQL root password here
MySQL database to create [dbispconfig]: <-- dbispconfig
MySQL charset [utf8]: <-- utf8
Shall this server join an existing ISPConfig multiserver setup (y,n) [n]: <-- y
MySQL master server hostname []: <-- web.example.tld
MySQL master server root username [root]: <-- root
MySQL master server root password []: <-- Enter the root password of the master server here
MySQL master server database name [dbispconfig]: <-- dbispconfig
Configure Mail (y,n) [y]: <-- y
Country Name (2 letter code) [AU]: <-- DE (Enter the ISO country code where you live here)
State or Province Name (full name) [Some-State]: <-- Niedersachsen (Enter the state where you live here)
Locality Name (eg, city) []: <-- Lueneburg (Enter the city here)
Organization Name (eg, company) [Internet Widgits Pty Ltd]: <-- ENTER
Organizational Unit Name (eg, section) []: <-- ENTER
Common Name (eg, YOUR name) []: <-- ENTER
Email Address []: <-- ENTER
Configure Jailkit (y,n) [y]: <-- n
Configure FTP Server (y,n) [y]: <-- n
Configure DNS Server (y,n) [y]: <-- n
Configure Apache Server (y,n) [y]: <-- n
Configure Firewall Server (y,n) [y]: <--y
Install ISPConfig Web-Interface (y,n) [y]: <--n
Run...
rm -f /var/www/ispconfig
... to remove the ISPConfig interface link in the /var/www directory.
Clean up the install directories:
rm -rf /tmp/ispconfig3_install/install
rm -f /tmp/ISPConfig-3-stable.tar.gz

4 Installing The MySQL Database Server

 
Edit the hosts file and add the IP addresses and hostnames for all servers. The hostnames and IP addresses have to be adjusted to match your setup.
vi /etc/hosts
127.0.0.1       localhost
192.168.0.105   web.example.tld
192.168.0.106   mail.example.tld
192.168.0.107   db.example.tld
192.168.0.108   ns1.example.tld
192.168.0.109   ns2.example.tld
 
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Set the hostname of the server:
echo db.example.tld > /etc/hostname
/etc/init.d/hostname.sh start
Run...
apt-get update
... to update the apt package database; then run...
apt-get upgrade
... to install the latest updates (if there are any).
It is a good idea to synchronize the system clock with an NTP (network time protocol) server over the Internet. Simply run...
apt-get -y install ntp ntpdate
... and your system time will always be in sync.
Install MySQL client and server:
apt-get -y install mysql-client mysql-server
Enter the new password for MySQL when requested by the installer.
We want MySQL to listen on all interfaces, not just localhost, therefore we edit /etc/mysql/my.cnf and comment out the line bind-address = 127.0.0.1:
vi /etc/mysql/my.cnf
[...]  

# Instead of skip-networking the default is now to listen only on  
# localhost which is more compatible and is not less secure.  
#bind-address           = 127.0.0.1  

[...]
Then restart MySQL:
/etc/init.d/mysql restart
Then install install the commandline version of PHP to be able to run PHP-based shell scripts for ISPConfig:
apt-get -y install php5-cli php5-mysql php5-mcrypt mcrypt
Install fail2ban: This is optional but recommended, because the ISPConfig monitor tries to show the log:
apt-get install fail2ban
Next install ISPConfig 3 on this server. To get the download URL of the latest ISPConfig 3 stable release, please visit the ISPConfig website: http://www.ispconfig.org/ispconfig-3/download/
Download the latest ISPConfig 3 stable release:
cd /tmp
wget http://www.ispconfig.org/downloads/ISPConfig-3-stable.tar.gz
tar xfz ISPConfig-3-stable.tar.gz
cd ispconfig3_install/install/
Then start the install script:
php -q install.php
Select language (en,de) [en]: <-- en
Installation mode (standard,expert) [standard]: <-- expert
Full qualified hostname (FQDN) of the server, eg server1.domain.tld [db.example.tld]: <-- db.example.tld
MySQL server hostname [localhost]: <-- localhost
MySQL root username [root]: <-- root
MySQL root password []: <-- Enter your MySQL root password here
MySQL database to create [dbispconfig]: <-- dbispconfig
MySQL charset [utf8]: <-- utf8
Shall this server join an existing ISPConfig multiserver setup (y,n) [n]: <-- y
MySQL master server hostname []: <-- web.example.tld
MySQL master server root username [root]: <-- root
MySQL master server root password []: <-- Enter the root password of the master server here
MySQL master server database name [dbispconfig]: <-- dbispconfig
Configure Mail (y,n) [y]: <-- n
Configure Jailkit (y,n) [y]: <-- n
Configure FTP Server (y,n) [y]: <-- n
Configure DNS Server (y,n) [y]: <-- n
Configure Apache Server (y,n) [y]: <-- n
Configure Firewall Server (y,n) [y]: <--y
Install ISPConfig Web-Interface (y,n) [y]: <--n
Run...
rm -f /var/www/ispconfig
... to remove the ISPConfig interface link in the /var/www directory.
Clean up the install directories:
rm -rf /tmp/ispconfig3_install/install
rm -f /tmp/ISPConfig-3-stable.tar.gz

5 Installing The Primary DNS Server

 
Edit the hosts file and add the IP addresses and hostnames for all servers. The hostnames and IP addresses have to be adjusted to match your setup.
vi /etc/hosts
127.0.0.1       localhost
192.168.0.105   web.example.tld
192.168.0.106   mail.example.tld
192.168.0.107   db.example.tld
192.168.0.108   ns1.example.tld
192.168.0.109   ns2.example.tld
 
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Set the hostname of the server:
echo ns1.example.tld > /etc/hostname
/etc/init.d/hostname.sh start
Run...
apt-get update
... to update the apt package database; then run...
apt-get upgrade
... to install the latest updates (if there are any).
It is a good idea to synchronize the system clock with an NTP (network time protocol) server over the Internet. Simply run...
apt-get -y install ntp ntpdate
... and your system time will always be in sync.
Install MySQL client and server:
apt-get -y install mysql-client mysql-server
Enter the new password for MySQL when requested by the installer.
Then install install the commandline version of PHP to be able to run PHP-based shell scripts for ISPConfig:
apt-get -y install php5-cli php5-mysql php5-mcrypt mcrypt
Install fail2ban: This is optional but recommended, because the ISPConfig monitor tries to show the log:
apt-get install fail2ban
Install BIND DNS Server:
apt-get -y install bind9 dnsutils
Next install ISPConfig 3 on the dns server. To get the download URL of the latest ISPConfig 3 stable release, please visit the ISPConfig website: http://www.ispconfig.org/ispconfig-3/download/
Download the latest ISPConfig 3 stable release:
cd /tmp
wget http://www.ispconfig.org/downloads/ISPConfig-3-stable.tar.gz
tar xfz ISPConfig-3-stable.tar.gz
cd ispconfig3_install/install/
Then start the install script:
php -q install.php
Select language (en,de) [en]: <-- en
Installation mode (standard,expert) [standard]: <-- expert
Full qualified hostname (FQDN) of the server, eg server2.domain.tld [ns1.example.tld]: <-- ns1.example.tld
MySQL server hostname [localhost]: <-- localhost
MySQL root username [root]: <-- root
MySQL root password []: <-- Enter your MySQL root password here
MySQL database to create [dbispconfig]: <-- dbispconfig
MySQL charset [utf8]: <-- utf8
Shall this server join an existing ISPConfig multiserver setup (y,n) [n]: <-- y
MySQL master server hostname []: <-- web.example.tld
MySQL master server root username [root]: <-- root
MySQL master server root password []: <-- Enter the root password of the master server here
MySQL master server database name [dbispconfig]: <-- dbispconfig
Configure Mail (y,n) [y]: <-- n
Configure Jailkit (y,n) [y]: <-- n
Configure FTP Server (y,n) [y]: <-- n
Configure DNS Server (y,n) [y]: <-- y
Configure Apache Server (y,n) [y]: <-- n
Configure Firewall Server (y,n) [y]: <--y
Install ISPConfig Web-Interface (y,n) [y]: <--n
Run...
rm -f /var/www/ispconfig
... to remove the ISPConfig interface link in the /var/www directory.
Clean up the install directories:
rm -rf /tmp/ispconfig3_install/install
rm -f /tmp/ISPConfig-3-stable.tar.gz

6 Installing The Secondary DNS Server

 
Edit the hosts file and add the IP addresses and hostnames for all servers. The hostnames and IP addresses have to be adjusted to match your setup.
vi /etc/hosts
127.0.0.1       localhost
192.168.0.105   web.example.tld
192.168.0.106   mail.example.tld
192.168.0.107   db.example.tld
192.168.0.108   ns1.example.tld
192.168.0.109   ns2.example.tld
 
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
Set the hostname of the server:
echo ns2.example.tld > /etc/hostname
/etc/init.d/hostname.sh start
Run...
apt-get update
... to update the apt package database; then run...
apt-get upgrade
... to install the latest updates (if there are any).
It is a good idea to synchronize the system clock with an NTP (network time protocol) server over the Internet. Simply run...
apt-get -y install ntp ntpdate
... and your system time will always be in sync.
Install MySQL client and server:
apt-get -y install mysql-client mysql-server
Enter the new password for MySQL when requested by the installer.
Then install install the commandline version of PHP to be able to run PHP-based shell scripts for ISPConfig:
apt-get -y install php5-cli php5-mysql php5-mcrypt mcrypt
Install fail2ban: This is optional but recommended, because the ISPConfig monitor tries to show the log:
apt-get install fail2ban
Install BIND DNS Server:
apt-get -y install bind9 dnsutils
Next install ISPConfig 3 on the dns server. To get the download URL of the latest ISPConfig 3 stable release, please visit the ISPConfig website: http://www.ispconfig.org/ispconfig-3/download/
Download the latest ISPConfig 3 stable release:
cd /tmp
wget http://www.ispconfig.org/downloads/ISPConfig-3-stable.tar.gz
tar xfz ISPConfig-3-stable.tar.gz
cd ispconfig3_install/install/
Then start the install script:
php -q install.php
Select language (en,de) [en]: <-- en
Installation mode (standard,expert) [standard]: <-- expert
Full qualified hostname (FQDN) of the server, eg server2.domain.tld [ns2.example.tld]: <-- ns2.example.tld
MySQL server hostname [localhost]: <-- localhost
MySQL root username [root]: <-- root
MySQL root password []: <-- Enter your MySQL root password here
MySQL database to create [dbispconfig]: <-- dbispconfig
MySQL charset [utf8]: <-- utf8
Shall this server join an existing ISPConfig multiserver setup (y,n) [n]: <-- y
MySQL master server hostname []: <-- web.example.tld
MySQL master server root username [root]: <-- root
MySQL master server root password []: <-- Enter the root password of the master server here
MySQL master server database name [dbispconfig]: <-- dbispconfig
Configure Mail (y,n) [y]: <-- n
Configure Jailkit (y,n) [y]: <-- n
Configure FTP Server (y,n) [y]: <-- n
Configure DNS Server (y,n) [y]: <-- y
Configure Apache Server (y,n) [y]: <-- n
Configure Firewall Server (y,n) [y]: <--y
Install ISPConfig Web-Interface (y,n) [y]: <--n
Run...
rm -f /var/www/ispconfig
... to remove the ISPConfig interface link in the /var/www directory.
Clean up the install directories:
rm -rf /tmp/ispconfig3_install/install
rm -f /tmp/ISPConfig-3-stable.tar.gz

7 Adjust The Server Settings In ISPConfig

 
Log into ISPConfig on the master server with a web browser:
http://192.168.0.105:8080
Click on System > Server services > web.example.tld and disable all checkboxes except of the Webserver and Fileserver checkbox and click on Save.

Click on System > Server services > mail.example.tld and disable all checkboxes except of the Mailserver checkbox and click on Save.

Click on System > Server services > db.example.tld and disable all checkboxes except of the DB-Server checkbox and click on Save.

Click on System > Server services > ns1.example.tld and disable all checkboxes except of the DNS-Server checkbox and click on Save.

Click on System > Server services > ns2.example.tld and disable all checkboxes except of the DNS-Server checkbox and select ns1.example.com in the Is mirror of Server selectbox and click on Save.


8 Links






No comments:

Post a Comment

Post a Comment